Video
How to apply
Material Safety and
Datasheet
FAQs
Nanoplas website
Ceralube

TPI distributes the following products produced by NanoPlas Inc. in India.

NANOMOLD COATING

Nanotechnology is of the fastest growing scientific and engineering disciplines worldwide. It is currently being used in fields such as bioscience, medicine, engineering, pharmacology, material sciences, and defense to name a few.

TPI brings a simple yet world class moulding solution – NANOMOLD COATING. This is the ideal choice for plastics and rubber processors in today's competitive manufacturing environment .

TPI is the exclusive distributor for Nanomold Coating and Cera-Lube products from Nanoplas,Inc., USA.

NanoMold Coating dramatically increases production output while reducing costs association with manual part removal, costly mould release agents, part scrap, slow cycle times, and repetitive mould maintanence due to sticking problems.

Wonderful features of Nanomold Coating:

• Withstands temperatures of between -50F ~ 1000°F
• Hydrophobic and oleophobic, yet vapor permeable
• Transparent film thickness of 100-200nm
• Low coefficient of friction
• Designed to resist most common chemical cleaners
• Offers corrosion protection
• Can be used on all tool steel and aluminum surfaces
• Can be used to release all thermoplastic, thermoset, and rubber materials
• Non-Toxic

Typical Moulding Problems

• Parts sticking in the mould
• Moulds not filling properly
• Streaking and drag marks
• Mould release contamination
• Extended cycle times
• Constant use of mould release agents

is the ideal choice for plastics and rubber processors in today's competitive manufacturing environment

NanoMold Coating dramatically increases production output while reducing costs association with manual part removal, costly mould release agents, part scrap, slow cycle times, and repetitive mould maintanence due to sticking problems.

Benefits of NanoMold Coating

• Reduces cycle times, increases productivity
• Eliminates sticking
• In-house/Self applied application
• Improves part quality
• Improves part finish by eliminating dragging and streching
• Reduces molding pressure and temperature
• Reduction in part weight due to lower packing pressures
• Does not migrate to part surface
• Up to 3,00,000 cycles per coating
• Withstands temperatures up to 1000 degrees F
• Can be used for virtually any moulded material
• One 5ml kit can coat up to 7-10 sqft of flat smooth mould surface
• 3 different kits available 5ml, 15ml, 25ml
• Kits include everything for application
• Nontoxic
• Not a mould release, its a Mould Coating

Applications

PC/ABS parts with complex details	Polyolefin parts	Polycarbonate parts
Small ABS parts	ABS parts with 160 pin holes

CERA-LUBE NANOCERAMICGREASE

is a leading edge, extremely high-performance lubricant that has a wide range of industrial applications. Cera-Lube™ utilizes nano ceramic particles that act as sub-microscopic ball bearings, providing continuous lubrication to metallic surfaces. Cera-Lube™ gives you 10x the normal life, a much lower coefficient of friction at all temperatures, extraordinary adhesion, and higher load-bearing properties than traditional “high performance greases”.

Features/Benefits:

• Staying Power—extraordinary adhesion extends production to 10 times that of other greases.
• Shear Stability—does not soften or run out. After 100,000 production strokes, shows no evidence of breaking down.
• Operating Temperatures—operates in a normal range from –40° F to 800° F, plus ceramic particles remain intact up to 2500° F.
• Extreme Pressure & Anti-Wear Protection—resists EP, provides exceptional stability without using lead, antimony, chlorine, zinc, barium, etc.
• Corrosion Resistant—resists water, steam, acid, and other chemicals.
• High Dropping Point—maintains viscosity across full temperature range, returning to normal viscosity after cooling.
• Low Coefficient of Friction—lower than PTFE greases.
• Chemically Insert—environmentally friendly.
• Low Dielectric Constant—excellent insulator.
• NSF Food Certified Available.